S_StripSlideTransitionTransitions between two clips by breaking them into strips and sliding them off the screen one at a time to reveal the incoming clip.In the Sapphire Transitions effects submenu.
Inputs:
|
|
Parameters:
-
Load Preset:
Push-button
.
Brings up the Preset Browser to browse all available presets for this effect.
-
Save Preset:
Push-button
.
Brings up the Preset Save dialog to save a preset for this effect.
-
Amount:
Default:
0,
Range:
-0.5 to 1.5.
Determines the transition ratio between the From and To inputs, and would normally be animated from 0 to 1 to perform a complete transition. The curve controlling this parameter can be adjusted for more detailed control over the timing of the wipe.
-
Style:
Popup menu, Default: Slide Off
.
Controls which clip the slide is applied to.
-
Slide Off:
The outgoing clip slides off to reveal the incoming clip.
- Slide On: The incoming clip slides on over the outgoing clip.
- Side by Side: The outgoing clip slides off while the incoming clip slides on next to it.
- Slide On: The incoming clip slides on over the outgoing clip.
-
Slide Off:
The outgoing clip slides off to reveal the incoming clip.
-
Motion Blur:
Default:
0.3,
Range:
0 or greater.
Scales the amount of motion blur to use.
-
Strip Size:
Default:
0.1,
Range:
0.01 or greater.
The width of the strips. This parameter can affect the timing of the strips, so animating it is not recommended.
-
Randomize Size:
Default:
0,
Range:
0 or greater.
Makes some strips larger and some smaller, at random.
-
Strip Angle:
Default:
0,
Range:
any.
Controls the angle along which the strips are divided, and also the direction in which they slide. This parameter can affect the timing of the strips, so animating it is not recommended.
-
Strip Shift:
Default:
0,
Range:
any.
Adjusts the position of the strip boundaries. This parameter can affect the timing of the strips, so animating it is not recommended.
-
Speed:
Default:
10,
Range:
1 or greater.
The speed at which each strip moves. As speed increases, the delay between strips becomes larger. If the speed is low, many strips will be in motion at the same time, creating a wave or ripple effect. This parameter affects the timing of the strips, so animating it is not recommended.
-
Slow Start:
Default:
1,
Range:
0 to 1.
Controls the acceleration of each strip as it moves. If set to zero, the strip will start moving at full speed. With larger values, the strip will start moving more slowly and accelerate up to its full speed, resulting in smoother motion.
-
Order:
Popup menu, Default: Top Down
.
Controls the order in which the strips slide off screen.
-
Top Down:
in order from top to bottom.
- Bottom Up: in order from bottom to top.
- Random: random order.
- Center Out: outward from the center, alternating strips above and below the center.
- Edges In: inward from the edges, alternating strips above and below the center.
- Bottom Up: in order from bottom to top.
-
Top Down:
in order from top to bottom.
-
Seed:
Default:
0.123,
Range:
0 or greater.
Initializes the random number generator for random strips sizes and order. The actual seed value is not significant, but different seeds give different results and the same value should give a repeatable result.
-
Crop Input Parameters:
Default:
0,
Range:
0 or greater.
These 4 parameters, Crop Top , Crop Bottom , Crop Left, and Crop Right , allow selecting a rectangular subsection of the input image to be processed. If the Wrap parameters are set to "No" the exposed borders will be transparent. If the Wrap is "Tile" or "Reflect" the source image is wrapped on the new cropped borders to fill the frame. This can make it easier to avoid artifacts due to distorting an image with bad edges.