S_GetFrameRetrieves a specified frame from the source clip for each destination frame. This is meant to be used by animating the value of Get Frame to speed up, slow down, or reverse the input clip in an arbitrary way as desired.In the Sapphire Time effects submenu.
Inputs:
|
Parameters:
-
Load Preset:
Push-button
.
Brings up the Preset Browser to browse all available presets for this effect.
-
Save Preset:
Push-button
.
Brings up the Preset Save dialog to save a preset for this effect.
-
Mocha Project:
Default:
0,
Range:
0 or greater.
Brings up the Mocha window for tracking footage and generating masks.
-
Blur Mocha:
Default:
0,
Range:
0 or greater.
Blurs the Mocha Mask by this amount before using. This can be used to soften the edges or quantization artifacts of the mask, and smooth out the time displacements.
-
Mocha Opacity:
Default:
1,
Range:
0 to 1.
Controls the strength of the Mocha mask. Lower values reduce the intensity of the effect.
-
Invert Mocha:
Check-box, Default:
off.
If enabled, the black and white of the Mocha Mask are inverted before applying the effect.
-
Resize Mocha:
Default:
1,
Range:
0 to 2.
Scales the Mocha Mask. 1.0 is the original size.
-
Resize Rel X:
Default:
1,
Range:
0 to 2.
The relative horizontal size of the Mocha Mask.
-
Resize Rel Y:
Default:
1,
Range:
0 to 2.
The relative vertical size of the Mocha Mask.
-
Shift Mocha:
X & Y, Default:
[0 0],
Range:
any.
Offsets the position of the Mocha Mask.
-
Bypass Mocha:
Check-box, Default:
off.
Ignore the Mocha Mask and apply the effect to the entire source clip.
-
Show Mocha Only:
Check-box, Default:
off.
Bypass the effect and show the Mocha Mask itself.
-
Combine Masks:
Popup menu, Default: Union
.
Determines how to combine the Mocha Mask and Input Mask when both are supplied to the effect.
-
Union:
Uses the area covered by both masks together.
- Intersect: Uses the area that overlaps between the two masks.
- Mocha Only: Ignore the Input Mask and only use the Mocha Mask.
- Intersect: Uses the area that overlaps between the two masks.
-
Union:
Uses the area covered by both masks together.
-
Get Frame:
Default:
0,
Range:
0 or greater.
The frame number of the source clip to access. This parameter should be animated to control the desired changes in motion. (If the Get Frame parameter is not animated it will just give a single still frame of that number for the entire clip.)
-
Interp Frames:
Check-box, Default:
off.
Selects the method to use for non-integer frame number references. If disabled, the nearest integer frame number is used with no interpolation. If enabled, it performs a weighted interpolation between the two nearest integer frame numbers and usually gives smoother results for slow motions.
-
Mask Use:
Popup menu, Default: Luma
.
Determines how the Mask input channels are used to make a monochrome mask.
-
Luma:
the luminance of the RGB channels is used.
- Alpha: only the Alpha channel is used.
- Alpha: only the Alpha channel is used.
-
Luma:
the luminance of the RGB channels is used.
-
Blur Mask:
Default:
0.05,
Range:
0 or greater.
Blurs the Mask input by this amount before using. This can provide a smoother transition between the masked and unmasked areas. It has no effect unless the Mask input is provided.
-
Invert Mask:
Check-box, Default:
off.
If on, inverts the mask input so the effect is applied to areas where the Mask is black instead of white. This has no effect unless the Mask input is provided.
See Also:
-
TimeWarpRGB
MotionDetect
TimeSlice
FreezeFrame
JitterFrames
RandomEdits
ReverseEdits
ReverseClip
Sapphire Plug-ins Introduction