S_DistortWarps the source input clip using the gradient of the Lens input clip. This can generate optical glass-like effects as if the source clip were being viewed through an arbitrarily shaped lens. It is best demonstrated when the lens image contains just a few bold shapes or a simple texture.In the Sapphire Distort category.
Inputs:
|
|
Parameters:
-
Load Preset:
Push-button
.
Brings up the Preset Browser to browse all available presets for this effect.
-
Save Preset:
Push-button
.
Brings up the Preset Save dialog to save a preset for this effect.
-
Mocha:
Default:
0,
Range:
0 or greater.
Brings up the Mocha window for tracking footage and generating masks.
-
Blur Mocha:
Default:
0,
Range:
any.
Blurs the Mocha Mask by this amount before using. This can be used to soften the edges or quantization artifacts of the mask, and smooth out the time displacements.
-
Mocha Opacity:
Default:
1,
Range:
0 to 1.
Controls the strength of the Mocha mask. Lower values reduce the intensity of the effect.
-
Invert Mocha:
Check-box, Default:
off.
If enabled, the black and white of the Mocha Mask are inverted before applying the effect.
-
Resize Mocha:
Default:
1,
Range:
0 to 2.
Scales the Mocha Mask. 1.0 is the original size.
-
Resize Rel X:
Default:
1,
Range:
0 to 2.
The relative horizontal size of the Mocha Mask.
-
Resize Rel Y:
Default:
1,
Range:
0 to 2.
The relative vertical size of the Mocha Mask.
-
Shift Mocha:
X & Y, Default:
screen center.
Offsets the position of the Mocha Mask.
-
Bypass Mocha:
Check-box, Default:
off.
Ignore the Mocha Mask and apply the effect to the entire source clip.
-
Show Mocha Only:
Check-box, Default:
off.
Bypass the effect and show the Mocha Mask itself.
-
Combine Masks:
Popup menu, Default: Union
.
Determines how to combine the Mocha Mask and Input Mask when both are supplied to the effect.
-
Union:
Uses the area covered by both masks together.
- Intersect: Uses the area that overlaps between the two masks.
- Mocha Only: Ignore the Input Mask and only use the Mocha Mask.
- Intersect: Uses the area that overlaps between the two masks.
-
Union:
Uses the area covered by both masks together.
-
Fine:
Check-box, Default:
off.
If enabled, the warping amount is reduced by a factor of 100. This mode is meant to allow subtle expansion or contraction of the source image near the edges of its matte given as the Lens input.
-
Amount:
Default:
1,
Range:
any.
The severity of the lens distortions. Make negative to invert the direction of the distortions.
-
Amount Rel:
X & Y, Default:
[1 1],
Range:
0 or greater.
The relative amounts of horizontal and vertical distortion. This has no effect unless Amount is positive.
-
Blur Lens:
Default:
0.5,
Range:
any.
Smooths out the edges in the lens image by this amount before using it.
-
Rotate Warp Dir:
Default:
0,
Range:
any.
Rotates the warping direction by this many degrees. If non-zero, this can add some unusual twisting effects to the lens distortion.
-
Wrap:
X & Y, Popup menu, Default:
[
Reflect Reflect
].
Determines the method for accessing outside the borders of the source image.
-
No:
gives black beyond the borders.
- Tile: repeats a copy of the image.
- Reflect: repeats a mirrored copy. Edges are often less visible with this method.
- Tile: repeats a copy of the image.
-
No:
gives black beyond the borders.
-
Filter:
Check-box, Default:
on.
If enabled, the image is adaptively filtered when it is resampled. This gives a better quality result when parts of the image are warped smaller.
-
Blur Mask:
Default:
0,
Range:
any.
Blurs the Mask input by this amount before using. This can provide a smoother transition between the masked and unmasked areas. It has no effect unless the Mask input is provided.
-
Invert Mask:
Check-box, Default:
off.
If on, inverts the mask input so the effect is applied to areas where the Mask is black instead of white. This has no effect unless the Mask input is provided.
-
Mask Use:
Popup menu, Default: Luma
.
Determines how the Mask input channels are used to make a monochrome mask.
-
Luma:
the luminance of the RGB channels is used.
- Alpha: only the Alpha channel is used, or if there is no valid Alpha channel the Red channel is used.
- Alpha: only the Alpha channel is used, or if there is no valid Alpha channel the Red channel is used.
-
Luma:
the luminance of the RGB channels is used.